PERMABOND HH167

Harmonization Code : 3403.19 | Lubricating Preparations (With 70% or More Petroleum Oils) For Automotive and Other Uses

PERMABOND HH167

Main features

  • Worn-Shaft and Damaged-Feature Metal Repair
  • 0.5 mm Gap Filling for Worn Metal Interfaces
  • Very-High-Strength Anaerobic Retention

Product Description

Permabond HH167 is a high-viscosity anaerobic retaining compound for metal repair and gap-filling retention in close-fitting metal assemblies. It is used to rebuild worn shafts and repair damaged threads, keyways and splines, with a maximum gap fill of 0.5 mm. The paste cures at room temperature when confined between mating metal surfaces and reaches typical handling strength on M10 steel in 15 minutes at 23 deg C. After cure, HH167 develops typical 32 MPa shear strength on a steel collar-and-pin test to ISO 10123, making it a very-high-strength option for repair and retention work.

Key features

  • Metal repair for worn interfaces: Repairs worn shafts, damaged threads, keyways and splines while retaining close-fitting metal parts.
  • 0.5 mm gap-filling retention: Fills gaps up to 0.5 mm for worn or damaged metal interfaces.
  • Very-high-strength cured retention: Typical shear strength is 32 MPa on a steel collar-and-pin test to ISO 10123.

Applications

Repair of worn shafts; repair of damaged threads, keyways and splines; retaining and gap filling of close-fitting metal parts.

Product Family

PERMABOND HH167

Loading pricing…
TDS, SDS & Technical Documents

Technical Specifications

General Properties
Appearance
Appearance at room temperature.
Silver
Chemistry Type
Acrylic
Specific Gravity
Specific gravity (SG) is the ratio of the density of a substance to the density of a reference substance; equivalently, it is the ratio of the mass of a substance to the mass of a reference substance for the same given volume. For liquids, the reference substance is almost always water (1), while for gases, it is air (1.18) at room temperature. Specific gravity is unitless.
1.1
Physical Properties
Viscosity
Viscosity is a measurement of a fluid’s resistance to flow. Viscosity is commonly measured in centiPoise (cP). One cP is defined as the viscosity of water and all other viscosities are derived from this base. MPa is another common unit with a 1:1 conversion to cP. A product like honey would have a much higher viscosity -around 10,000 cPs- compared to water. As a result, honey would flow much slower out of a tipped glass than water would. The viscosity of a material can be decreased with an increase in temperature in order to better suit an application
500,000 mPa.s
Electrical Properties
Dielectric Strength
Dielectric strength is measured in kV per mm and is calculated by the Breakdown voltage divided by the thickness of the tested material. Those two properties go hand in hand and while Breakdown voltage is always thickness dependent, dielectric strength is a general material property. As an example, the dielectric strength of Polyimide is 236 kV/mm. If we place 1mm of Polyimide between two electrodes, it will act as an insulator until the voltage between the electrodes reaches 236 kV. At this point it will start acting as a good conductor, causing sparks, potential punctures and current flow.
11 kV/mm
Thermal Properties
Thermal Conductivity
Thermal conductivity describes the ability of a material to conduct heat. It is required by power packages in order to dissipate heat and maintain stable electrical performance. Thermal conductivity units are [W/(m K)] in the SI system and [Btu/(hr ft °F)] in the Imperial system.
0.19 W/m.K

Additional Information

Technical properties

As-supplied / before-processing properties

PropertyValueUnitMethod / condition
Chemical compositionAcrylic-Uncured material
Viscosity500,000 at 2 rpm; 90,000 at 20 rpmcPUncured material; 25 deg C
Specific gravity1.1-Uncured material
Storage temperature5 to 25deg CManufacturer storage guidance
Technical properties

After-processing / final-state properties

PropertyValueUnitMethod / condition
Break torque45N mTypical cured material; M10 steel; ISO 10964
Prevailing torque32N mTypical cured material; M10 steel; ISO 10964
Shear strength32MPaTypical cured material; steel collar and pin; ISO 10123

Leading Brands Trust in Our Products and Services

Products that Perform| Knowledge that Serves| Service that Delivers